Коды ошибок> 119
К
ОДЫ
ОШИБОК
NOTES:
1.
mmm
= the setup of “Paper Supply”
2.
ppp
= the setup of “Media Type
3. “yy” in code denotes paper size. Paper size codes are
shown in the list after the table.
CODE
LCD MESSAGE
DETAILS
10007
Check The Printer
Indicates that job cancellation has been
initiated and data is being ignored until
job is complete.
10053,
10976,
10975,
10050,
10054,
10051,
10052
Printer Error
These are not a user-level errors. Please
call service
40994
Check The Printer
Memory limitation.
This error code appears if memory full
occurs during multiple copy.
10982
Check The Printer
Job cancelled because there is no
permission for printing (Related to
JobAccount). Cleared by pressing the
ON-LINE switch.
30114
Check The Printer
Invalid data was received.
Press the On-line switch to cancel.
Displayed when an unsupported PDL
command is received or a spool
command is received without a HDD.
411yy
Check The Printer
Manual paper feed is required. Manually
insert the paper shown by mmm.
480yy,4
82yy,48
3yy
Media Mismatch
Check The Printer
The media type in the tray does not
match the print data. Load mmm/ppp
paper in MP Tray orTray1.
480yy,4
82yy,48
3yy
Media Mismatch
Check The Printer
The media size or both media size and
media type in the tray does not match
the print data.
30993
Check The Printer
Network initializing.
472yy
Tray1 Empty
Load mmm in Tray1
Printing request has been issued to an
empty tray1.
Поддон вставлен, а надпись на дисплее Tray missing / Empty tray/ Вставить поддон не исчезла.
Наиболее часто такая неисправность характерна для кофемашин Jura моделей S90,S95,X90,S7,S9, а также для некоторых моделей Bosch, siemens,Nivona.
За наличие правильности установки поддона отвечают металлические контакты поддона расположенные на тыльной стороне.
Контакты поддона срабатывают если:
- > лоток/поддон был только установлен.
- > лоток/поддон был заполнен водой.
Если лоток/поддон не был установлен, электрическая цепь разомкнута.
ОТСУТСТВИЕ ПОДДОНА отображается.
Когда лоток/поддон был установлен,контакт поддона замыкает цепь.
Прибор готов к использованию.
Когда лоток/поддон полон водой, контакты поддона установлены в воду. Электрическое сопротивление между контактами поддона замкнуты, и идет сигнал на модуль питания.
На дисплее отображается: ПУСТОЙ ПОДДОН.
Если на дисплее не гаснет надпись Вставить поддон/Tray missing/Empty tray, несмотря на наличие пустого поддона/лотка, то могут присутствовать остатки воды или влаги между контактами.
Тщательно очистите поддон в области контактов с помощью мыльного раствора, а затем просушите.
Однако, если эти меры не помогли или возникли сразу после приготовления кофе,
то велика вероятность, что это неисправность нагревательного элемента или пластиковых деталей. В случае образования утечки воды в этих элементах вода
скапливается в защитном поддоне расположенном под нагревательным элементом, этот поддон предохраняет попадание воды на электрические элементы,
и имеет специальный желобок для стока воды в основной поддон, расположенный как раз над контактами.
Примечание:
На многих моделях кофемашин, на лоток/поддон устанавливается дополнительный микропереключатель,
приводимый в действие триггером на поддоне.
Если лоток/поддон выдвинут, микропереключатель открывается и прерывает источник питания к двигателю механизма через модуль питания.
10976,
10975,
10950,
10054,
10051,
10052
call service
This error code appears if memory full occurs during multiple copy.
JobAccount). Cleared by pressing the ON-LINE switch.
Press the On-line switch to cancel.
Displayed when an unsupported PDL command is received or a spool
command is received without a HDD.
82yy,48
3yy
Check The Printer
paper in MP Tray or Tray1.
media type in the tray does not match
the print data.
Check The Printer
Load mmm in Tray1
Load mmm in MP Tray
Loading mmm paper and pressing the On-line switch will start printing.
Check The Printer
Replace Y Toner
Replace Y Toner
replacement is necessary (Y, M or C).
Replace Y Toner
Replace K Toner
Replace Y Toner
Warning status takes effect at Cover Open/Close. Allows printing approx 50 pages (Letter 5% duty, density 5%).
Replace M Toner
Replace C Toner
Toner? Yes/No
M Toner? Yes/No
C Toner? Yes/No
40960,
40961,
40962
Check The Printer
Sensor.
Check The Printer
recovery printing, and continue.
Replace Belt
40035,
40036
Check The Printer
Check The Printer
Check The Printer
Check The Printer
Check The Printer
Show download data is being received.
Receiving of download data has finished.
An error occurs when received download data has:
1 : Size error
2 : Checksum error
3 : Print Model N0. error
4 :Module I/F version error
5 : FAT version error
Download data is writing.
Writing download data has finished.
An error occurs when writing download data has:
1 : Memory allocation error
2 : Download File error
3 : Device free space reserving error
4 : Device free space insufficient error
5 : File Write error
6 : CU-F/W mismatch error
Check The Printer
>> … When printing from Chrome on Windows, it tries to print from Tray 1 …
>> … There is a «print using system dialogue» link that I can click. When I click that, I see that «autoselect» is selected, and it prints just fine from Tray 2 as it should …
>> … If I try to print from Android or Mac, I get the error message as it tries to print from Tray 1 …
Which probably implies that the print jobs generated by the Chrome (without «using system dialogue«, Android and Mac systems / applications contain printer language ‘instructions’ related to identifying paper size and/or paper type and/or paper source which are at odds with what the printer believes it has available in tray 2 (probably paper type = Plain amd paper size = A4 (most of the world) or = Letter (in USA).
… and if so, the printer is merely doing what is has been requested to do, and no amount of change to the printer firmware could alter the subsequent observed behaviour.
If we could ‘capture’ as sample print job to a file, analysis would tell us what is being requested by these jobs.
On a Windows system, using a standard Print dialogue, such a ‘capture’ is achieved by selecting the «print to file» option in the Print dialogue.
I have no idea whether or not Chrome, Android or Mac offer an equjivalent ‘capture’ feature.
Содержание
- Страница 138: Решение проблемы замятия бумаги
- Adf cover
- Установите барабан переноса изображений, оснащенный картрид.
- Ус тр а не ни е неисправност ей .
- Когда можно увидеть документ внутри АПД .
- Сообщения об ошибке, Сообщения об ошибке, отображенные на экране, 7 сообщения об ошибке
- Сообщения об ошибке .
- Сообщения об ошибке .
- Сообщения об ошибке .
Страница 138: Решение проблемы замятия бумаги
7. Устранение неисправностей
В данной главе имеются способы решения проблем, которые могут быть обнаружены при работе с устройством.
В данной главе объяснено, как решить проблему замятия бумаги.
Для получения подробной информации о каждом компоненте компьютера, см.
Для получения подробной информации о местонахождении каждого компонента устройства, см.
Проверка сообщений об ошибках
Когда происходит замятие бумаги, на экране
дисплея появится сообщение [Paper jam] или
[Document jam] и замигает кнопка на панели оператора. Код ошибки и
описание отличаются в зависимости от того, где
происходит замятие бумаги.
Проверьте код ошибки, который появится из списка
снизу, и см. соответствующую процедуру для
решения проблемы замятия бумаги.
Решение проблемы замятия
бумаги
Убедитесь, что внутри устройства не осталось бумаги.
Осторожно извлеките бумагу, чтобы не порвать. Если это
произойдет, извлеките все остатки.
Барабан переноса изображений (зеленый ролик) очень
хрупкий. Обращайтесь с ним осторожно.
Не подвергайте барабан переноса изображений прямому
воздействию солнечных лучей или слишком яркому
внутреннему свету (примерно более чем 1500 люксов). Даже
при нормальном внутреннем освещении не оставляйте его
более чем на 5 минут.
Код ошибки 370, 371, 372 (дуплексное
замятие бумаги)
Извлеките документы из лотка подачи
документов, если там таковые имеются.
Нажмите кнопку открытия верхней крышки
(1) и откройте верхнюю крышку.
Paper Jam Occurs: 3##С
Please open the scanner unit and the top
cover And, please check.
Автор Musa задал вопрос в разделе Железо
Принтер говорит: «Open top cover. и получил лучший ответ
Ответ от Отправитель[гуру]
Откройте верхнюю крышку,
Удалите (снимите) контейнер с тонером (картридж видимо) ,
Затем проверьте уровень экрана,
Удалите застрявшую бумагу (замятую)
Установите картридж на место
И закройте верхнюю крышку.
Короче у тебя принтер бумагу зажевал походу.
Если нижний край бумаги виден,
удерживайте бумагу и осторожно
вытаскивайте.
Убедитесь, что внутри устройства не осталось бумаги.
Осторожно извлеките бумагу, чтобы не порвать. Если это
произойдет, извлеките все остатки.
Блок разгрузки бумаги (Замятие бумаги)
Если нижний край бумаги в принтере виден,
удерживайте и вытаскивайте бумагу
осторожно.
Если видно замятие бумаги в блоке разгрузки бумаги и если
бумага видна изнутри верхней крышки, вытащите буагу по
направлению внутрь принтера.
Если нижний край бумаги не виден, но виден
верхний край в блоке разгрузки бумаги,
удерживайте верхний край бумаги и
осторожно вытаскивайте бумагу. Если
невозможно извлечь бумагу, следуя шагам
(А)1 и (А)2, вытаскивайте бумагу при помощи
следующих шагов (В).
Если не удалось извлечь замятую бумагу, не
прилагайте усилий, чтобы ее извлечь, а
следуйте нижеприведенным шагам.
Поместите картридж барабана переноса
изображений обратно в принтер и закройте
верхнюю крышку.
Сначала выключите питание принтера (О), а
затем снова включите (I). Когда движок начнет
крутиться, удерживайе верхний край бумаги и
вытаскивайте бумагу.
Если замятие бумаги происходит, когда Вы загружаете бумагу,
проверьте, чтобы она не оставалась ни в одном боке подачи
бумаги. Помните, что можно сбросить сигнальный дисплей
только тогда, когда откроете верхнюю крышку, а затем снова ее
закроете.
Установите барабан переноса изображений, оснащенный картрид.
Установите барабан переноса изображений,
оснащенный картриджем, заново,
убедившись, что выступы (1&2) находятся в
правильном положении в слотах с каждой
стороны принтера (3).
Убедитесь, что внутри устройства не осталось бумаги.
Осторожно извлеките бумагу, чтобы не порвать. Если это
произойдет, извлеките все остатки.
Закройте верхнюю крышку.
Код ошибки 390 (Замятие подачи бумаги
(Многоцелевой лоток))
Извлеките документы из лотка подачи
документов, если там таковые имеются.
Нажмите кнопку открытия верхней крышки
(1) и откройте верхнюю крышку.
Осторожно выберите барабан переноса
изображений, оснащенный картриджем. Не
дотрагивайтесь и не поцарапайте
поверхность зеленого барабана.
Если верхний край бумаги виден с тыльной
стороны прозрачных направляющих,
поверните их в сторону печки и держите
верхний край бумаги и осторожно
вытаскивайте бумагу.
Если не виден ни верхний ни нижний
край бумаги, переместите замятую
бумагу в сторону стрелки как
показано. держивайте верхний край
бумаги и осторожно вытаскивайте
Если нижний край бумаги виден,
удерживайте бумагу и осторожно
вытаскивайте.
Убедитесь, что внутри устройства не осталось бумаги.
Осторожно извлеките бумагу, чтобы не порвать. Если это
произойдет, извлеките все остатки.
Ус тр а не ни е неисправност ей .
Установите барабан переноса изображений,
оснащенный картриджем, заново,
убедившись, что выступы (1&2) находятся в
правильном положении в слотах с каждой
стороны принтера (3).
Закройте верхнюю крышку.
Код ошибки 391, 392 (Замятие подачи
бумаги)
Код ошибки 391 указывает на ошибку в лотке 1 и код
ошибки 392 указывает на замятие бумаги в лотке 2.
Лоток 1 приведен в качестве примера для данной процедуры.
Вытащите и удалите кассету для бумаги
указанного лотка.
Извлеките замятую бумагу.
Поместите лоток обратно в устройство.
Нажмите кнопку открытия верхней крышки
(1) и откройте верхнюю крышку.
Закройте верхнюю крышку.
Произошло замятие документа
Когда можно увидеть документ в
дуплексном пути прохождения бумаги
Откройте крышку АПД и извлеките документ
по направлению вверх.
Когда можно увидеть документ внутри АПД .
Когда можно увидеть документ внутри
АПД
Извлеките документы из лотка подачи
документов, если там таковые имеются.
Откройте крышку АПД.
Удерживайте замятую бумагу за верхний
край и осторожно вытащите ее.
Если верхний край документа виден из под
направляющих (1), поднимите их, а затем вытащите
документ.
Если сторона документа не видна в АПД, поднимите
лоток подачи документов (2), а затем вытащите
документ.
Вытащите лоток подачи документов.
Закройте крышку АПД.
Сообщения об ошибке, Сообщения об ошибке, отображенные на экране, 7 сообщения об ошибке
Общие сообщения об ошибках для всех функций
Сообщения об ошибке
Сообщения об ошибке
В данном разделе объяснены причины и способы их удаления для сообщений об ошибках, отображенных на
экране отображения и функция кнопки .
Сообщения об ошибке, отображенные на экране
В следующих списках:
— «%COLOR%» указывает на К (черный)
— «%TRAY%» указывает на лоток 1, лоток 2 или МЦ лоток
— «%ERRCODE%» указывает на код ошибки
— «%FS_ERR%», «%CODE%» и «%FATALSTRING1%» указывают на детальную информацию об ошибках
— «%MEDIA_SIZE%» указывает на размер бумаги
— «%MEDIA_TYPE%» указывает на тип бумаги
— «%COVER%» указывает на верхнюю крышку или заднюю крышку.
Если отображенное сообщение содержит текст «Смотрите раздел Помощи для получения подробной информации», ожно проверить
контрмеры ошибок, нажав кнопку на панели оператора.
Если отображено сообщение «
на панели управления для удаления ошибки.
Для получения подробной информации о функции кнопки , см.
Общие сообщения об ошибках для всех функций
Требуется проверка.
PU Flash Error
Ошибка прошивки.
Обратитесь к дилеру.
Требуется проверка.
PU Communication Error
Ошибка прошивки.
Обратитесь к дилеру.
%COLOR% Toner Low.
Please see Help for details.
Загорается* Картридж указанного цвета на исходе.
Приготовьте новый картридж.
* Если кнопка > [Установки Админ.] >
[Device Management] > [Установки Системы] > [Near life LED]
установлена на [Disable], кнопка не
включается.
Image Drum Unit Near Life.
Please see Help for details.
Загорается* Срок эксплуатации блока барабана переноса
изображений подходит к концу.
Подготовьте к замене барабан переноса
изображений.
* Если кнопка >[Установки Админ.] >
[Device Management] > [Установки Системы] > [Status in Near
life] установлена на [Enable] и [Near life LED] установлено на
[Disable], кнопка не включается.
Если [Status in Near life] установлено на [Disable], сообщение не
отображается и кнопка не включается.
%COLOR% Toner Empty
%ERRCODE%
Please see Help for details.
Картридж указанного цвета пуст.
Замените его на новый картридж.
413 : К
Сообщения об ошибке .
Сообщения об ошибке
%COLOR% Toner Empty
Please see Help for details.
Загорается Картридж указанного цвета пуст.
Замените его на новый картридж.
%COLOR% Toner cartridge not installed. :
%ERRCODE%
Please see Help for details.
Картридж указанного цвета установлен неправильно.
Установите его заново.
613 : К
%COLOR% Toner cartridge not installed.
Please see Help for details.
Загорается Картридж указанного цвета установлен неправильно.
Установите его заново.
Please see Help for details.
Загорается Указанный лоток пуст.
Загрузите бумагу в лоток.
File System is full.
Please see Help for details.
Загорается Файловая система заполнена.
File System is write protected.
Please see Help for details.
Загорается Файловая система, в которую Вы пытались записать,
защищена от записи.
Please see Help for details.
Память переполнена.
Если выполняются несколько заданий
одновременно, завершите их и попробуйте снова.
Если не работает, уменьшите разрешение печати.
Memory Overflow. : 420
Please see Help for details.
Память переполнена.
Уменьшите разрешение печати. Если не работает,
уменьшите размер печатных данных.
Access Limitation Error
Deleted unauthorized user data.
Please see Help for details.
Загорается Устройство удалило задание
Accounting Log Buffer is near full.
Please see Help for details.
Загорается Журнал учета заданий почти заполнен.
Accounting Log Buffer Full (Delete old logs)
Загорается Старые учетные журналы удалены, так как журнал
учета заданий почти заполнен.
Сообщения об ошибке .
Сообщения об ошибке
Accounting Log Writing Error
Please see Help for details.
Загорается Ошибка записи заданий в журнал учета.
Disk Use Failed %FS_ERR%
Please see Help for details.
Ошибка операции диска.
Please check data.
Message Data Write Error : %CODE%.
Загорается Ошибка записи сообщений для загрузки.
Обратитесь к дилеру.
Please check %COLOR% Toner Cartridge.
Please see Help for details.
Загорается Что-то не в порядке с сенсором картриджа
указанного цвета во время печати.
Проверьте, что картридж указанного цвета
установлен правильно.
Please check %COLOR% Toner Cartridge. :
%ERRCODE%
Please see Help for details.
Что-то не в порядке с сенсором картриджа
указанного цвета.
Проверьте, что картридж указанного цвета
установлен правильно.
543 : К
Please check %COLOR% Toner Cartridge. :
%ERRCODE%
Please see Help for details.
Картридж указанного цвета не зафиксирован
должным образом.
Проверьте рычажок фиксации, чтобы он скользил
влево.
547 : К
Paper Jam: %ERRCODE%
Please open the scanner unit and the top cover.
Please see Help for details.
Замятие бумаги.
Удалите замятую бумагу.
Ошибка 372: Застревание из дуплекса
Ошибка 380: Подача бумаги
Ошибка 381: Транспорт
Ошибка 382: Выход
Ошибка 389: Потеря печатной страницы
Ошибка 390: МЦ Лоток
Ошибка 390: Ручной
Paper Jam: %ERRCODE%
Please pull out the paper cassette of the indicated
tray.
Please see Help for details.
Произошло замятие бумаги при подаче бумаги из
указанного лотка.
Удалите замятую бумагу.
391 : Лоток 1
392 : Лоток 2
Please check the %COVER%.: %ERRCODE%
Please check the %COVER%.
Please see Help for details.
Открыта верхняя крышка.
Закройте верхнюю крышку.
310 : Верхняя крышка
587 : Задняя крышка
Please see Help for details.
Крышка АПД открыта.
Закройте крышку АПД.
Сообщения об ошибке .
Сообщения об ошибке
Выключите и включите питание
%ERRCODE%: Error
Произошла ошибка в устройстве.
Выключите устройство, а затем снова включите его.
Если ошибка не удалена, обратитесь к дилеру.
Требуется проверка.
%ERRCODE: Error
Произошла ошибка в устройстве.
Обратитесь к дилеру.
Выключите и включите питание
%ERRCODE%: Error %FATALSTRING1%
Произошла ошибка в устройстве.
Выключите устройство, а затем снова включите его.
Если появится такая же ошибка, выключите
устройство, а затем снова включите его. Если
ошибка не удалена или такая же ошибка появляется
снова, обратитесь к дилеру.
Document Jam
Please open the scanner unit and the ADF cover.
Please see Help for details.
Замятие документа.
Откройте крышку АПД, а затем извлеките замятую
бумагу.
Lamp Error. Please call service.
Please see Help for details.
Указывает на ошибку лампочки.
Данное сообщение отображается, так как
интенсивность света лампочки слабее.
Обратитесь к дилеру.
Please see Help for details.
Загорается Кассета бумаги отсутствует в указанном лотке.
Вставьте кассету бумаги в указанный лоток.
Если кассета уже помещена в устройство, вытащите
ее и установите заново в нужном положении.
Please close %TRAY%.: 430,440
To cancel, select [Cancel]
Кассета бумаги отсутствует в указанном лотке.
Вставьте кассету бумаги в указанный лоток.
Если кассета уже помещена в устройство, вытащите
ее и установите заново в нужном положении.
Требуется проверка.
%ERRCODE%: SIP Error
Обработка отсканированного изображения не
удалась.
Выключите устройство, а затем снова включите его.
Если ошибка не удалена, обратитесь к дилеру.
Please call service.
Scanner unit failed to detect printer unit.
Ошибка между блоками сканера и принтера.
Выключите устройство, а затем снова включите его.
Если ошибка не удалена, обратитесь к дилеру.
SIP Firmware Missing
Обнаружена неполадка платы.
Выключите устройство, а затем снова включите его.
Если ошибка не удалена, обратитесь к дилеру.
Wait a moment.
Network initializing .
Загорается Измененные настройки сети сохранены.
Please change SD Memory Card.
Error Code: 085
Загорается Содержимое SD карты не может быть прочитано
нормально.
Если та же карта используется далее, может
произойти та же ошибка. Замените SD карту.
Выключите и включите питание
Carriage Error
Please see Help for details.
Указывает на ошибку картриджа.
Сообщение отображается, так как картридж сканера
работает ненормально.
Если ошибка не удалена, обратитесь к дилеру.
Выключите и включите питание
Carriage Error
Указывает, что произошла следующая ошибка
картриджа.
2: Ошибка исходного положения (ошибка
соединения картриджа)
3: Ошибка определения стартовой позиции
сканирования
Если ошибка не устраняется, обратитесь к Вашему
дилеру.
Error Message List
Wait a moment. Network initializing .
The network is being initialized.
Wait for a while until the machine connects to the network.
Checking File System
File system in the hard disk is being checked. Wait for a while.
Inspection is required. PU Flash Error
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
Inspection is required. PU Communication Error
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
Offline Mode
The machine is offline. Press the Online button to set it to [Online].
Data present.
Data remains unprinted.
Deleting data.
The job was cancelled or user is unauthorized.
Warming up.
The machine is adjusting the temperature of the fuser unit. Wait for a while.
Preparing .
Color registration and density are being adjusted. Wait for a while.
Updating firmware. Do not turn OFF the power.
The programs on the machine are being updated.
Do not turn the machine off until the update completes.
The machine automatically restarts after the update completes.
Toner Low.
The toner indicated on the screen is low. Have a new toner cartridge ready.
Waste Toner Full Replace with new Toner Cartridge.
Waste toner is full. Replace the toner cartridge with a new one.
C: Cyan (blue), M: Magenta (red)
C Non Recommended Toner.
An optimum C (Cyan, blue) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
M Non Recommended Toner.
An optimum M (Magenta, red) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
Y Non Recommended Toner.
An optimum Y (Yellow) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
K Non Recommended Toner.
An optimum K (Black) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
Error Postscript
A postscript error has occurred.
Image Drum Near Life.
The image drum indicated on the screen is near life. Have a new image drum ready.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Fuser Near Life.
The fuser unit is near life. Have a new fuser unit ready.
Belt Unit Near Life.
The belt unit is near life. Have a new belt unit ready.
Fuser Unit Life. Install New Fuser Unit.
The fuser unit reaches its lifetime.
Replace the fuser unit with a new one.
Belt Unit Life. Install New Belt Unit.
The belt unit reaches its lifetime.
Replace the belt unit with a new one.
Toner empty. Replace with new Toner Cartridge.
The toner indicated on the screen is empty. Replace the empty toner cartridge with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Toner cartridge not installed.
A color toner cartridge indicated on the screen is not installed.
Install the toner cartridge.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Life. Please install new Image Drum Unit.
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
TRAY is empty.
No paper is loaded in the tray. Load paper.
File System is full.
Memory in the file system is full.
Delete unnecessary files.
The File System is write-protected.
The file you are trying to write is write-protected.
Check the file name.
Insufficient page memory to collate.
Insufficient memory error has occurred during collate printing.
Reduce the number of pages to print.
Insufficient memory. Error: 014
Memory full error has occurred during PC Fax reception. Press [Close].
Unauthorized user, job cancelled.
Unauthorized job was sent or unauthorized user attempted to print or send a fax. Data was deleted. Contact your administrator to use this machine.
File erasing .
Files stored for authentication print are being deleted.
Wait for a while.
Deleting encrypted authentication print data.
Files stored for encrypted authentication print are being deleted. Wait for a while.
Erased Data Full
Files supposed to be deleted are full. Erase the files.
Secure job storage period exceeded.
Files whose authentication print data storage period expired were automatically deleted.
Disk Read/Write Error
An error has occurred in the file system. Press [Close].
Flash Error
An error has occurred when firmware was being updated.
Contact the administrator.
Invalid print data received.
Invalid print data or PC fax data was received. To erase the message, press [Close].
If you performed authentication printing, the data was deleted because it was incomplete. Print again.
Received data has been discarded because Job Type is restricted.
Data whose job type is not defined in the acceptable job type settings was received. The data was discarded without being processed.
Select a job type defined in the acceptable job type settings for [Job Type] of the printer driver and print again.
Manual Request. Error : 500
Print on paper fed manually. Load paper in the MP tray.
Please change [MEDIA_SIZE] [MEDIA_TYPE] in [TRAY]. Error: 461, 462, 463, 464
The size and type of fed paper do not match those indicated on the screen. Use the same size and type of paper selected on the application.
Please change [MEDIA_SIZE] [MEDIA_TYPE] in MP Tray Error: 460
The size and type of paper loaded in the MP tray do not match those indicated on the screen. Make sure that the size and type of paper loaded in the MP tray match those selected on the application.
Wait a moment. Message Data processing .
Messages to be displayed on the machine are being updated. Wait for a while.
Wait a moment. Message Data writing .
Messages to be displayed on the machine are being updated. Wait for a while.
Restart the machine. Writing message data has been complete.
Messages to be displayed on the machine are now updated.
Turn the machine off, and then back on.
Wait for a while.
Please check data. Message Data Write Error
Updating messages to be displayed on the machine failed.
Make sure that you use right data for this machine.
Wait a moment. Network Configuration writing .
Network settings for this machine is changed. The new settings are being stored. Wait for a while.
Wait a moment. Network initializing .
Network settings for this machine are initializing.
Paper [TRAY] is empty Set [MEDIA_SIZE] Error: 490, 491, 492, 493, 494
No paper is loaded in the indicated tray. Load paper of the displayed size.
[TRAY] cassette is missing. Open and Close the indicated cassette. Error: 440, 441, 442, 430, 431, 432, 433
The tray is not installed. Install the cassette. If the cassette is already inserted, pull it out, and then insert it again.
Insufficient memory. Error: 420
Data is too complicated. Memory full error has occurred during processing. Reduce the volume of the print data.
Waste Toner Full Replace with new Toner Cartridge. Error: 414, 415, 416, 417
Waste toner of the toner cartridge is full. Opening and closing the front cover can resume printing for a while, but it may damage the image drum. Replace the toner cartridge with a new one as soon as possible.
C: Cyan (blue), M: Magenta (red)
Toner empty. Replace with new Toner Cartridge. Error: 410, 411, 412, 413
The indicated cartridge ran out of toner.
Opening and closing the front cover can resume printing for a while, but it may damage the image drum. Replace the toner cartridge with a new one as soon as possible.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Incompatible C Toner. Error: 552, 556, 616, 622
The installed C (Cyan, blue) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Incompatible M Toner. Error: 551, 555, 615, 621
The installed M (Magenta, red) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Incompatible Y Toner. Error: 550, 554, 614, 620
The installed Y (Yellow) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Incompatible K Toner. Error: 553, 557, 617, 623
The installed K (Black) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Toner Not Installed. Error: 610, 611, 612, 613
A color toner cartridge indicated on the screen is not installed.
Install the toner cartridge.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Sensor Error Check Image Drum. Error: 540, 541, 542, 543
The sensor error has occurred in the image drum indicated on the screen.
Uninstall the image drum, and then install it again.
If the message persists, uninstall the toner cartridge and install it again.
If the toner cartridge is not installed, install it.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Multiple sheets of paper have been fed. Reset Paper in [TRAY]. Error: 401
The indicated tray fed multiple sheets of paper at a time.
Remove the cassette from the tray, and then load paper again.
Paper Size Error. Reset Paper in [TRAY]. Error: 400
Paper size error has occurred in the indicated tray. Make sure that the size made by paper loaded in the tray matches the setting made by the paper size dial in the paper cassette. Load paper according to the paper size and direction set for the paper size dial.
If the setting made by the paper size dial is wrong, cancel printing first, set the paper size dial, and then print again.
Make sure that the cassette does not feed multiple sheets of paper at a time after starting printing. If it happens, remove paper, and then load paper correctly.
Paper jam has occurred. Open the front cover and remove the paper. Error: 390
Paper jammed via the paper feed path from the MP tray.
If the edge of the jammed paper is not visible, open the front cover and remove the paper.
Paper jam has occurred. Pull out the [TRAY] cassette and then remove the paper. Error: 391, 392, 393, 394
A paper jammed via the paper feed path from the indicated tray.
Pull out the cassette, and then remove paper. If multiple sheets of paper are fed at a time, remove paper and reload paper.
Make sure that the paper stoppers are set in the right position.
Paper jam has occurred. Open the front cover and remove the paper. Error: 372, 380
Paper jammed in the paper feed path of the machine. Open the front cover and remove the jammed paper.
A paper jam has occurred under the image drum or around the fuser unit. Please remove paper. Error: 381, 382, 383, 348, 389
A paper jam has occurred inside the machine.
Open the cover and remove jammed paper.
A Paper Jam has occurred and paper remains near the Duplex Unit. Please remove paper. Error: 370, 371, 373
Paper jammed near the duplex printing unit.
Pull out the duplex unit on the back of the machine, and then remove jammed paper.
The 2-Sided Printing unit is not set correctly. Error: 360
The duplex unit is not properly installed. Install the duplex unit.
Image Drum Life. Please install new Image Drum Unit. Error: 350, 351, 352, 353
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible, however.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Life. Please install new Image Drum Unit. Error: 560, 561, 562, 563, 564, 565, 566, 567
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Life. Please install new Image Drum Unit. Error: 680, 681, 682, 683
Printing has stopped because the image drum indicated on the screen reached its lifetime. Replace with a new image drum to print.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Fuser Unit Life. Install New Fuser Unit. Error: 354
The fuser unit reaches its lifetime.
Replace the fuser unit with a new one.
Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible for maintaining the print quality.
Belt Unit Life. Install New Belt Unit. Error: 355
The belt unit reaches its lifetime.
Replace the belt unit with a new one.
Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible for maintaining the print quality.
The Fuser Unit is not installed correctly. Reset Fuser Unit. Error: 348
The fuser unit is not properly installed. Remove and re-install the fuser unit. If the error persists after re-installing, replace the fuser unit with a new one.
Waste Toner Full. Install New Belt Unit. Error: 356
Waste toner of the belt unit is full. Replace the belt unit with a new one. Opening and closing the cover can resume printing. Printing stops after 500 sheets are printed.
Toner cartridge not properly installed. Error: 544, 545, 546, 547
A color toner cartridge indicated on the screen is not installed.
Make sure that the lever on the toner cartridge is fully turned and the protective tape is removed.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum not properly installed. Check Image Drum. Error: 340, 341,342, 343
The indicated image drum is not installed correctly.
Remove and re-install the image drum.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
The Fuser Unit is not installed correctly. Reset Fuser Unit. Error: 320
The fuser unit is not properly installed. Remove and re-install the fuser unit.
Belt Unit not installed correctly. Re-set the Belt Unit. Error: 330
The belt unit is not properly installed. Remove and re-install the belt unit.
[COVER] Open. Error: 310, 311, 587
Indicated cover is open. Close the cover.
Error: 310 The output tray, 311 The front cover, 587 The upper output tray
Please check data. Program Data Write Error
An error occurred when firmware was being updated.
Use a correct update file.
Power OFF/ON
Turn the machine off, and then back on.
If the same error occurs, contact your dealer.
Inspection is required.
Turn the machine off, and then back on.
If the same error occurs, contact your dealer.
Cancelling .
The cancel button was pressed while copying. The copy job is being cancelled. Wait for a while.
Automatic document feeder (ADF) cover is open.
The ADF cover of the scanner is open. Close the cover.
Document jam has occurred. Open the automatic document feeder (ADF) cover on the scanner to check.
Paper jammed in the ADF of the scanner.
Open the ADF cover and remove jammed paper.
Multiple sheets of document have been fed. Open the automatic document feeder (ADF) cover on the scanner to check.
Multiple sheets of document have been fed. Fan a stack of the paper well and place them on the automatic document feeder (ADF). Use the document glass if a tag or label is affixed to the document.
Scanner lamp error check the lamp.
Light volume of the scanner is low. Contact your dealer.
Power OFF/ON Carriage Error
An error has occurred on the carriage of the scanner. Turn the machine off, and then back on.
If the same error occurs, contact your dealer.
USB Memory Full
Scan To USB Memory was cancelled because the USB Memory is full.
Check the free space in the USB Memory.
Writing to USB memory failed.
The USB Memory is write-protected. Unlock the protection.
USB Memory disconnected.
The USB Memory was removed while performing Scan To USB Memory.
Connect to PC failed.
No destination computer was found for Scan to Computer. Make sure that your computer is turned on and recordable.
To erase the message, press [Close].
Insufficient memory occurred during Rx.
Memory full error has occurred during fax reception. Ensure available memory.
Communication Error
An error has occurred during fax transmission or fax reception.
Telephone
The external phone is in use.
File Transmission Error
An error such as a malfunction of the server or disconnection of a network cable has occurred while performing Scan To shared folder.
Check the network connection.
To erase the message, press [Close].
E-mail Transmission Error
An error such as a malfunction of the server or disconnection of a network cable has occurred while performing Scan To E-mail. Check the network connection.
To erase the message, press [Close].
Please check SMTP settings.
Cannot connect to the SMTP server. Check the network settings.
Please check POP3 settings.
Cannot connect to the POP3 server. Check the network settings.
SMTP Login failed.
An attempt to log into the SMTP server ended up an authentication error.
Check the network settings.
SMTP Auth. Unsupported
The SMTP server does not support the authentication system.
Check the network settings.
POP3 Login failed.
An attempt to log into the POP3 server ended up an authentication error.
Check the network settings.
Getting target IP failed. Please Check DHCP settings.
The DHCP server cannot be detected. Check the network connection.
Please check DNS settings.
Cannot connect to the DNS server. Check the network connection.
Please check Server settings.
Cannot connect to the file server. Check the network settings.
Server Login failed.
Logging into the file server failed. Check the server settings.
Entering directory failed.
Connecting to the directory of the FTP server failed. Check the server settings.
Changing data Transfer Type failed.
File transmission failed because the file transfer type was not accepted by the FTP server. Change the FTP transfer type to «binary».
File writing failed.
Files sent using Scan To shared folder could not be written. Check the access rights for the shared folder.
FTP destination Full.
Memory in the FTP server is low. Delete unnecessary files and ensure the free space.
Please change File Name.
The specified file name is not acceptable. Check the FTP server settings and change the file name.
Device communication protocol not supported.
The server does not support CIFS or FTP. Check the server settings.
Please check Network Share Name.
The name of the network shared folder is not correct. Check the folder name.
Please check data. Program Data Write Error
An error has occurred when program was being updated.
Please insert USB Memory.
Scan To USB Memory or print from USB Memory with USB Memory not inserted was attempted.
Insert USB Memory.
[TRAY] cassette missing.
The cassette in the indicated tray is pulled out.
Install the cassette.
Access Limitation Error Monochrome printing was performed due to the color printing limitation.
A color print job was converted to a mono print job due to an unauthorized user. Contact your administrator for color printing.
Access Limitation Error Data was deleted due to the color printing limitation.
A color print job was deleted due to an unauthorized user. Contact your administrator for color printing.
Restricted access error Data deleted due to printing restrictions.
A print job was deleted due to an unauthorized user. Contact your administrator for printing.
Incompatible USB device connected. Remove the connected USB device.
An unsupported USB device is connected. Remove the USB device.
Please remove the connected USB device. USB device has not been recognized.
The connected USB device was not recognized. Remove the USB device.
Please remove the USB Hub. USB Hub is connected.
A USB hub is connected. Remove the USB hub. This machine does not support USB hub.
Inspection is required. SIP Error
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
Please call service. Scanner unit failed to detect printer unit.
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
HDD Error 0
While initializing this machine, a hard disk which needs formatting was detected.
HDD Error 250
While initializing this machine, a damaged file for encrypted authentication printing was found. Format the hard disk again.
Accounting Log buffer is near full.
The accounting log buffer is almost full.
Acquire the log and free the buffer.
Accounting Log Writing Error
An accounting log writing error has occurred.
To erase the message, press [Close].
Job Log Database Error
A data base access error has occurred while writing or reading the job log. Turning the machine off and on may resolve the problem.
To erase the message, press [Close].
Accounting Log Buffer Full (Delete old logs)
Old logs were deleted, because accounting log buffer was full. Acquire the log and free the buffer.
Power OFF/ON
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
A decoding error occurred. Check the image data.
An error has occurred in the image data sent to this machine. Check the image data.
Process has been canceled as there is no space on the device. Please free up enough memory space by reducing usage and try again.
Processing data was cancelled due to memory full.
Reduce the usage on the device to ensure available memory, and then retry.
Process has been canceled by a device error. After maintenance or change of the device, please try again.
Processing data was cancelled because an error occurred on the device.
Repair or replace the device, and then retry.
Access denied to PC. Please check PC.
Connecting to a computer failed when performing Scan to Computer. Check the settings on the computer.
Deleting data.
This machine ran out of color toner. Color print data is being deleted.
Error PDF
The PDF file is damaged.
This PDF file is password protected.
This PDF file is password protected. Enter a password to print.
Valid password required to print document.
This PDF needs authentication. Enter a password to print.
No communication with the SNTP server.
Obtaining current time from the SNTP server failed. Check the server.
USB Memory disconnected.
The USB Memory was removed while printing from USB Memory. Do not remove USB Memory while printing is in progress.
Cannot open the file.
The specified file could not be Opened. Check the file.
Cannot read the file.
Files could not be read. Check the device where the files are stored.
File loading from USB.
Data is being read from USB Memory.
Press the Stop button to cancel reading.
An error occurred. Scanning is pending.
Printing has stopped due to an error.
Image Drum Sensor Error.
The toner sensor error has occurred in the image drum indicated on the screen.
Printing was stopped. Rear Output Tray was opened during printing. Open the Output Tray. Error code: 409
The rear output tray was moved while printing.
Place the rear output tray in the correct position, and then open and close the output tray.
Toner empty. Replace with new Toner Cartridge.
The indicated cartridge ran out of toner.
Replace the empty toner cartridge with a new one.
Wait Timeout in menu is disabled. Printing is disabled except by USB. Clear page buffer and enable time out in menu.
Wait Timeout is disabled.
Insufficient memory occurred during Fax Tx reservation.
Insufficient memory error has occurred during Scan To fax.
Insufficient memory.
Insufficient memory error has occurred during fax reception.
E-mail receiving has been cancelled.
E-mail reception was cancelled.
Check the file format and size of the attached file.
Wireless settings are incomplete.
Wrong values are set or items remain unset in the wireless LAN settings. Check the wireless settings.
Not connected to wireless access point.
No wireless LAN access points are found.
Make sure that the access point is turned on.
Disconnect and re-connect to wireless LAN.
Wireless startup failed.
Restart the machine. If the error persists, contact your dealer.
Firmware Update Error Please try again. If network doesn’t work, please try firmware update over USB.
Updating the firmware failed. Update again.
Registering with Google Cloud Print. Don’t turn off the power until registration is complete.
This machine is being registered to the Google Cloud Print service. Wait for a while.
Deleting from Google Cloud Print.
This machine is being removed from the Google Cloud Print service. Wait for a while.
Caution, unknown Consumable detected Go to User Manual «Trouble Shooting» to restore operation Error 709
You can use any consumables in your product, but you must accept the risks of using non-genuine consumables.
If the use of non-genuine consumables causes damage to the product or results in your product not functioning to its full specification, then such damage or effect on the product is not covered by warranty.
To accept these risks and to restore function;
Turn off the machine.
Holding the [CLEAR] button, turn on the machine.
Release the [CLEAR] button when «RAM CHECK 100%» is displayed.
This operation log is recorded in the product.
If you have any questions, contact your dealer.
Replace the image drum. [PAGES] Pages Left.
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Replace the image drum. Print Quality Not Guaranteed.
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Receiving data timeout.
Data could not received within a certain period of time.
IPv4 address is conflicted. Please change IPv4 address.
The IP address assigned to this machine is duplicated with that of another device.
Check the IP addresses, and then assign another IP address.
Incompatible [COLOR] Image Drum. Error: 984, 685, 686, 687, 690, 691, 692, 693, 700, 701, 702, 703, 704, 705, 706, 707
Non-optimum image drum is installed.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
C Image Drum Not Installed. Error: 696
Cyan (blue) image drum is not installed.
Install the image drum.
M Image Drum Not Installed. Error: 695
Magenta (red) image drum is not installed.
Install the image drum.
Y Image Drum Not Installed. Error: 694
Yellow image drum is not installed.
Install the image drum.
K Image Drum Not Installed. Error: 697
Black image drum is not installed.
Install the image drum.
Blank pages were detected on all pages. Please check how the document was set.
Scanned pages are all blank. Turn over the document.
In order to set paper that cannot be output to the Upper Output Tray, the paper was output from Output Tray. To turn off this display, press the [Close] button.
Check the type of the specified paper.
Simplex printing was performed as the paper setting did not allow duplex printing.
Duplex printing is not available on the specified paper.
Check the size and thickness of paper.
Multi-purpose tray has not been set to be used as the tray, so multiple copies have been printed. Please verify multi-purpose tray settings. Press [Close] button to remove this dialog
MP tray setting is set to [Do Not Use]. Change the MP tray setting.
Output Paper Full. Remove the paper on [TRAY]. Error: 480, 485
Paper in the output tray is full.
Remove the handout.
Changing Language. Panel operation is disabled.
Display language is being changed.
Wait for a while.
Language Change Failed. Error num: %CODE%
Switching display languages failed. Press the power button to turn the machine off, and then back on.
Detected an abnormality of internal database. The data must be deleted. After pressing [Format], the data will be deleted, and then reboot.
Data base is beyond restoration.
To delete the data base, press [Format].
Cannot print because your Summary Account balance is 0. User name for Printing: [USERNAME] Summary Account Name for Insufficient Balance: [ACCOUNTNAME] To continue the print job, increase the balance and select [Start]. To increase the balance, please contact the device administr. To cancel the print job, select [Cancel].
The number of print jobs excesses the limit. No more print jobs are authorized. Contact your administrator.
Copyright © 2015 Oki Electric Industry Co., Ltd. All rights reserved.
Источник
Содержание
- Oki c822 toner sensor error
- Oki c822 toner sensor error
- Error Message List
Oki c822 toner sensor error
Причина в том, что принтер «не видит» прыгающей в своём окошке шторки датчика тонера (см. статью о механизме работы датчика). Есть пять простых вариантов причины возникновения этой проблемы:
1. Не до упора повёрнута ручка запирания тонер-картриджа. Окошко в торце ручки должно находиться строго напротив отверстия в корпусе принтера, за которым расположена оптопара датчика тонера. Нажмите ручку до упора.
2. На белую шторку, появляющуюся в окошке, налип тонер, отчего она перестаёт отражать свет оптопары. Шторку необходимо очистить от тонера, чтобы пропало сообщение об ошибке датчика.
3. В принтере, где уже побывал покупной картридж, оказался вновь стартовый. В комплекте поставки всех младших принтеров, начиная с лета 2004 года, идут стартовые тонер-картриджи, у которых нет датчика тонера (см. выше), а вместо него просто наклеен кусочек фольги. Такой картридж может нормально работать в принтере только с самого начала. При его наличии принтер считает расход тонера только по формуле и когда достчитывает до конца, требует заменить картридж. После этого в принтер необходимо установить покупной картридж, в котором есть датчик тонера. Как только такой картридж попадает в принтер, он переходит в режим контроля датчика тонера и если после этого в него опять вставить стартовый картридж, то принтер, не увидев работающего датчика, выдаст ошибку датчика тонера.
4. Размер окошка слишком велик. Возможна ситуация, когда окошко, за которым находится белая шторка, слишком велико и поэтому оптопара не может корректно сфокусировать отражение от шторки и получить устойчивое срабатывание. Исправить ситуацию можно следующим образом: необходимо заклеить чёрным не блестящим скотчем окошко сверху так, чтобы высота прорези была не более 4мм:
5. Установлен не тот фотокартридж. 
В нижней части фотокартриджа расположен небольшой металлический штифт (или несколько штифтов), которые попадают в прорези на металлической пластине, расположенной на правой части внутри принтера.
Штифты могут быть установлены в разные позиции. Именно положение штифтов определяет «совместимость» того или иного фотокартриджа с тем или иным принтером. Если в принтер вставлен фотокартридж не того типа, то картридж устанавливается в принтере не под нужным углом и окошко датчика тонера просто не попадает напротив оптопары. Штифт, в принципе, можно переставить, но для этого необходимо разобрать картридж, так как вынуть его наружу невозможно: на его конце находится шляпка, не позволяющая вытянуть его. Поэтому где-то эту причину тоже можно отнести к сложным вариантам. Впрочем, можно открутить металлическую пластину внутри принтера, ту самую, в которую упираются эти металлические штырьки, тогда в принтер можно будет установить печатный картридж от любого принтера 3000й или 5000й серии.
Теперь «сложные» варианты сами по себе. Вынув тонер-картридж и удерживая его в том же положении, как он стоит в принтере, покрутите пальцем шестерню снизу. Белая шторка должна периодически на короткое время убираться вверх из окошка. Если этого не происходит, значит возникла механическая проблема.
1. Заклинил рычажок датчика. Белая шторка застряла либо в верхнем либо в нижнем положении. Попробуйте вручную (например иголкой) раскачать шторку вверх и вниз. Обычно это можно сделать не разбирая картриджа.
2. Оторвалась мешалка внутри тонер-картриджа. При вращении шестерни мешалка не вращается внутри картриджа, отчего и шторка тоже не прыгает. Очевидно, что для восстановления работоспособности необходимо разобрать картридж и восстановить вращение мешалки.
3. В картридж засыпан магнитный тонер. О такой проблеме доводилось слышать только по отношению к чёрному картриджу, который пытались заправлять чёрным магнитным тонером от ч/б принтеров. Такой тонер, находящийся в картридже, «навсегда» притягивает к себе магнитик, отчего шторка уходит из своего окошка вверх, давая на датчике постоянное false. Решение очевидно – воспользоваться немагнитным тонером, тщательно вычистив внутренности тонер-картриджа от остатков магнитного порошка.
У новой серии принтеров С3000 и C5000 датчик тонера расположен в фотокартридже. Снаружи он виден как прямоугольное окошко, расположенное на торце фотокартриджа с той стороны, где располагается запирающая ручка тонер-картриджа:
Это окошко закрывается специальной шторкой, когда тонер-картридж отсоединяется от фотокартриджа (на рисунке ниже мигает красным, но на самом деле эта шторка — чёрная):
Так вот, ошибка датчика тонера может возникать на этих принтерах от того, что при закрывании ручки тонер-картриджа шторка не ушла наверх. В этом случае оптопара «не увидит» движущегося за окошком отражающего сектора, который и вызывает срабатывание оптопары. Соответственно, закрыть ручку тонер-картриджа до упора или если это не помогает, принять другие меры для того, чтобы эта шторка ушла вверх.
Источник
Oki c822 toner sensor error
mariam » 01:47 — 23.10.07
KudesNIK » 10:08 — 23.10.07
Гость » 10:33 — 23.10.07
До этого — печатали. Ошибка датчика синего тонера. Ничего особенного не делали, пару раз бумага застревала на ленте переноса, вытаскивала картриджи аккуратненько, извлекала бумагу и дальше печатала. Но это реально пару раз всего и было, и проблем не вызывало. Я конечно куплю сейчас новый картридж, и/или фотокартридж если проблема в нем, принтер очень нужен в рабочем состоянии и времени разбираться особенно нет, но все равно очень хочу понять что случилось и как быть в таких ситуциях. Заранее спасибо за помощь 
KudesNIK » 16:04 — 23.10.07
Вариантов с этим датчиком несколько.
1. Не до конца закрыта ручка, запирающая тонер-картридж в драм-картридже.
2. При закрытии картриджа не полностью поднялась шторка, закрывающая отверстие для отражалки в драм-картридже.
3. На оптопару насыпался тонер и свет просто не проходит
У меня тут пара фоток есть, ща я их обработаю и в соответствующий FAQ положу для простоты восприятия.
Кстати, в FAQ фотки и пояснения к ним уже прицепил, так что желающие могут их там посмотреть.
mariam » 16:53 — 24.10.07
Слов нет, одни эмоции. С тех пор как принтер встал, приходили два разных мальчика-ремонтника (не ОКИ, у нас нет специализированного сервиса в городе), чесали репы, бормотали что-то про чипы. А я, после недолгого, но проникновенного рассматривания новых картинок в «соответствующем FAQ» (не пойму как ссылки добавлять, простите) у KudesNIKa, залезла, что-то интуитивно поковыряла в окошке датчика, почистила на всяк. случ. еще раз оптопару, закрыла крышку и на глазах у изумленной публики принтер заработал.
KudesNIK
Спасибо! Мы будем покупать принтеры А3 формата, и тот факт, что это будут OKI во многом определил тот факт, что у OKI есть такой замечательный KudesNIK Я теперь Ваша фанатка.
KudesNIK » 10:33 — 25.10.07
mariam , а в каком городе у нас сервис-центр отсутствует? 
Судя по IP-адресу ты пишешь из Казани. А в Казани есть сервис по OKI. Но IP-адрес вещь неверная, поэтому расскажи, в какую сторону надо развиваться?
А ссылки просто вставляются — надо нажать кнопку URL и добавить нужную ссылку в тег
» [url=http:www.ссылка.ru] «, потом написать то, что должно появиться и снова нажать кнопку URL. Усё.
mariam » 12:30 — 25.10.07
В данный момент вещаю из г. Набережные Челны. Гипотетически сервис может и есть, но его никак не найти, мы честно и долго искали, с тех пор еще когда у нас старые ОКИ стояли. Опять же, теоретически Казань недалеко, но не тащиться же туда из-за мелких проблем. Картриджи и проч. заказываю через Инет и вожу Грузовозоффым, т.к. в городе в продаже тоже нету. Но, насколько мне известно, здесь не так много ОКИ вообще в городе, у нас два с5900, да еще пару мест всего знаю. Да и городишко малюсенький.
Источник
Error Message List
Wait a moment. Network initializing .
The network is being initialized.
Wait for a while until the machine connects to the network.
Checking File System
File system in the hard disk is being checked. Wait for a while.
Inspection is required. PU Flash Error
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
Inspection is required. PU Communication Error
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
Offline Mode
The machine is offline. Press the Online button to set it to [Online].
Data present.
Data remains unprinted.
Deleting data.
The job was cancelled or user is unauthorized.
Warming up.
The machine is adjusting the temperature of the fuser unit. Wait for a while.
Preparing .
Color registration and density are being adjusted. Wait for a while.
Updating firmware. Do not turn OFF the power.
The programs on the machine are being updated.
Do not turn the machine off until the update completes.
The machine automatically restarts after the update completes.
Toner Low.
The toner indicated on the screen is low. Have a new toner cartridge ready.
Waste Toner Full Replace with new Toner Cartridge.
Waste toner is full. Replace the toner cartridge with a new one.
C: Cyan (blue), M: Magenta (red)
C Non Recommended Toner.
An optimum C (Cyan, blue) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
M Non Recommended Toner.
An optimum M (Magenta, red) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
Y Non Recommended Toner.
An optimum Y (Yellow) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
K Non Recommended Toner.
An optimum K (Black) toner cartridge is not installed.
Use a toner cartridge that matches your machine.
Error Postscript
A postscript error has occurred.
Image Drum Near Life.
The image drum indicated on the screen is near life. Have a new image drum ready.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Fuser Near Life.
The fuser unit is near life. Have a new fuser unit ready.
Belt Unit Near Life.
The belt unit is near life. Have a new belt unit ready.
Fuser Unit Life. Install New Fuser Unit.
The fuser unit reaches its lifetime.
Replace the fuser unit with a new one.
Belt Unit Life. Install New Belt Unit.
The belt unit reaches its lifetime.
Replace the belt unit with a new one.
Toner empty. Replace with new Toner Cartridge.
The toner indicated on the screen is empty. Replace the empty toner cartridge with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Toner cartridge not installed.
A color toner cartridge indicated on the screen is not installed.
Install the toner cartridge.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Life. Please install new Image Drum Unit.
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
TRAY is empty.
No paper is loaded in the tray. Load paper.
File System is full.
Memory in the file system is full.
Delete unnecessary files.
The File System is write-protected.
The file you are trying to write is write-protected.
Check the file name.
Insufficient page memory to collate.
Insufficient memory error has occurred during collate printing.
Reduce the number of pages to print.
Insufficient memory. Error: 014
Memory full error has occurred during PC Fax reception. Press [Close].
Unauthorized user, job cancelled.
Unauthorized job was sent or unauthorized user attempted to print or send a fax. Data was deleted. Contact your administrator to use this machine.
File erasing .
Files stored for authentication print are being deleted.
Wait for a while.
Deleting encrypted authentication print data.
Files stored for encrypted authentication print are being deleted. Wait for a while.
Erased Data Full
Files supposed to be deleted are full. Erase the files.
Secure job storage period exceeded.
Files whose authentication print data storage period expired were automatically deleted.
Disk Read/Write Error
An error has occurred in the file system. Press [Close].
Flash Error
An error has occurred when firmware was being updated.
Contact the administrator.
Invalid print data received.
Invalid print data or PC fax data was received. To erase the message, press [Close].
If you performed authentication printing, the data was deleted because it was incomplete. Print again.
Received data has been discarded because Job Type is restricted.
Data whose job type is not defined in the acceptable job type settings was received. The data was discarded without being processed.
Select a job type defined in the acceptable job type settings for [Job Type] of the printer driver and print again.
Manual Request. Error : 500
Print on paper fed manually. Load paper in the MP tray.
Please change [MEDIA_SIZE] [MEDIA_TYPE] in [TRAY]. Error: 461, 462, 463, 464
The size and type of fed paper do not match those indicated on the screen. Use the same size and type of paper selected on the application.
Please change [MEDIA_SIZE] [MEDIA_TYPE] in MP Tray Error: 460
The size and type of paper loaded in the MP tray do not match those indicated on the screen. Make sure that the size and type of paper loaded in the MP tray match those selected on the application.
Wait a moment. Message Data processing .
Messages to be displayed on the machine are being updated. Wait for a while.
Wait a moment. Message Data writing .
Messages to be displayed on the machine are being updated. Wait for a while.
Restart the machine. Writing message data has been complete.
Messages to be displayed on the machine are now updated.
Turn the machine off, and then back on.
Wait for a while.
Please check data. Message Data Write Error
Updating messages to be displayed on the machine failed.
Make sure that you use right data for this machine.
Wait a moment. Network Configuration writing .
Network settings for this machine is changed. The new settings are being stored. Wait for a while.
Wait a moment. Network initializing .
Network settings for this machine are initializing.
Paper [TRAY] is empty Set [MEDIA_SIZE] Error: 490, 491, 492, 493, 494
No paper is loaded in the indicated tray. Load paper of the displayed size.
[TRAY] cassette is missing. Open and Close the indicated cassette. Error: 440, 441, 442, 430, 431, 432, 433
The tray is not installed. Install the cassette. If the cassette is already inserted, pull it out, and then insert it again.
Insufficient memory. Error: 420
Data is too complicated. Memory full error has occurred during processing. Reduce the volume of the print data.
Waste Toner Full Replace with new Toner Cartridge. Error: 414, 415, 416, 417
Waste toner of the toner cartridge is full. Opening and closing the front cover can resume printing for a while, but it may damage the image drum. Replace the toner cartridge with a new one as soon as possible.
C: Cyan (blue), M: Magenta (red)
Toner empty. Replace with new Toner Cartridge. Error: 410, 411, 412, 413
The indicated cartridge ran out of toner.
Opening and closing the front cover can resume printing for a while, but it may damage the image drum. Replace the toner cartridge with a new one as soon as possible.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Incompatible C Toner. Error: 552, 556, 616, 622
The installed C (Cyan, blue) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Incompatible M Toner. Error: 551, 555, 615, 621
The installed M (Magenta, red) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Incompatible Y Toner. Error: 550, 554, 614, 620
The installed Y (Yellow) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Incompatible K Toner. Error: 553, 557, 617, 623
The installed K (Black) toner cartridge is not optimum.
We recommend using an optimum toner cartridge.
Toner Not Installed. Error: 610, 611, 612, 613
A color toner cartridge indicated on the screen is not installed.
Install the toner cartridge.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Sensor Error Check Image Drum. Error: 540, 541, 542, 543
The sensor error has occurred in the image drum indicated on the screen.
Uninstall the image drum, and then install it again.
If the message persists, uninstall the toner cartridge and install it again.
If the toner cartridge is not installed, install it.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Multiple sheets of paper have been fed. Reset Paper in [TRAY]. Error: 401
The indicated tray fed multiple sheets of paper at a time.
Remove the cassette from the tray, and then load paper again.
Paper Size Error. Reset Paper in [TRAY]. Error: 400
Paper size error has occurred in the indicated tray. Make sure that the size made by paper loaded in the tray matches the setting made by the paper size dial in the paper cassette. Load paper according to the paper size and direction set for the paper size dial.
If the setting made by the paper size dial is wrong, cancel printing first, set the paper size dial, and then print again.
Make sure that the cassette does not feed multiple sheets of paper at a time after starting printing. If it happens, remove paper, and then load paper correctly.
Paper jam has occurred. Open the front cover and remove the paper. Error: 390
Paper jammed via the paper feed path from the MP tray.
If the edge of the jammed paper is not visible, open the front cover and remove the paper.
Paper jam has occurred. Pull out the [TRAY] cassette and then remove the paper. Error: 391, 392, 393, 394
A paper jammed via the paper feed path from the indicated tray.
Pull out the cassette, and then remove paper. If multiple sheets of paper are fed at a time, remove paper and reload paper.
Make sure that the paper stoppers are set in the right position.
Paper jam has occurred. Open the front cover and remove the paper. Error: 372, 380
Paper jammed in the paper feed path of the machine. Open the front cover and remove the jammed paper.
A paper jam has occurred under the image drum or around the fuser unit. Please remove paper. Error: 381, 382, 383, 348, 389
A paper jam has occurred inside the machine.
Open the cover and remove jammed paper.
A Paper Jam has occurred and paper remains near the Duplex Unit. Please remove paper. Error: 370, 371, 373
Paper jammed near the duplex printing unit.
Pull out the duplex unit on the back of the machine, and then remove jammed paper.
The 2-Sided Printing unit is not set correctly. Error: 360
The duplex unit is not properly installed. Install the duplex unit.
Image Drum Life. Please install new Image Drum Unit. Error: 350, 351, 352, 353
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible, however.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Life. Please install new Image Drum Unit. Error: 560, 561, 562, 563, 564, 565, 566, 567
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum Life. Please install new Image Drum Unit. Error: 680, 681, 682, 683
Printing has stopped because the image drum indicated on the screen reached its lifetime. Replace with a new image drum to print.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Fuser Unit Life. Install New Fuser Unit. Error: 354
The fuser unit reaches its lifetime.
Replace the fuser unit with a new one.
Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible for maintaining the print quality.
Belt Unit Life. Install New Belt Unit. Error: 355
The belt unit reaches its lifetime.
Replace the belt unit with a new one.
Opening and closing the cover can resume printing for a while. Replace with a new one as soon as possible for maintaining the print quality.
The Fuser Unit is not installed correctly. Reset Fuser Unit. Error: 348
The fuser unit is not properly installed. Remove and re-install the fuser unit. If the error persists after re-installing, replace the fuser unit with a new one.
Waste Toner Full. Install New Belt Unit. Error: 356
Waste toner of the belt unit is full. Replace the belt unit with a new one. Opening and closing the cover can resume printing. Printing stops after 500 sheets are printed.
Toner cartridge not properly installed. Error: 544, 545, 546, 547
A color toner cartridge indicated on the screen is not installed.
Make sure that the lever on the toner cartridge is fully turned and the protective tape is removed.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Image Drum not properly installed. Check Image Drum. Error: 340, 341,342, 343
The indicated image drum is not installed correctly.
Remove and re-install the image drum.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
The Fuser Unit is not installed correctly. Reset Fuser Unit. Error: 320
The fuser unit is not properly installed. Remove and re-install the fuser unit.
Belt Unit not installed correctly. Re-set the Belt Unit. Error: 330
The belt unit is not properly installed. Remove and re-install the belt unit.
[COVER] Open. Error: 310, 311, 587
Indicated cover is open. Close the cover.
Error: 310 The output tray, 311 The front cover, 587 The upper output tray
Please check data. Program Data Write Error
An error occurred when firmware was being updated.
Use a correct update file.
Power OFF/ON
Turn the machine off, and then back on.
If the same error occurs, contact your dealer.
Inspection is required.
Turn the machine off, and then back on.
If the same error occurs, contact your dealer.
Cancelling .
The cancel button was pressed while copying. The copy job is being cancelled. Wait for a while.
Automatic document feeder (ADF) cover is open.
The ADF cover of the scanner is open. Close the cover.
Document jam has occurred. Open the automatic document feeder (ADF) cover on the scanner to check.
Paper jammed in the ADF of the scanner.
Open the ADF cover and remove jammed paper.
Multiple sheets of document have been fed. Open the automatic document feeder (ADF) cover on the scanner to check.
Multiple sheets of document have been fed. Fan a stack of the paper well and place them on the automatic document feeder (ADF). Use the document glass if a tag or label is affixed to the document.
Scanner lamp error check the lamp.
Light volume of the scanner is low. Contact your dealer.
Power OFF/ON Carriage Error
An error has occurred on the carriage of the scanner. Turn the machine off, and then back on.
If the same error occurs, contact your dealer.
USB Memory Full
Scan To USB Memory was cancelled because the USB Memory is full.
Check the free space in the USB Memory.
Writing to USB memory failed.
The USB Memory is write-protected. Unlock the protection.
USB Memory disconnected.
The USB Memory was removed while performing Scan To USB Memory.
Connect to PC failed.
No destination computer was found for Scan to Computer. Make sure that your computer is turned on and recordable.
To erase the message, press [Close].
Insufficient memory occurred during Rx.
Memory full error has occurred during fax reception. Ensure available memory.
Communication Error
An error has occurred during fax transmission or fax reception.
Telephone
The external phone is in use.
File Transmission Error
An error such as a malfunction of the server or disconnection of a network cable has occurred while performing Scan To shared folder.
Check the network connection.
To erase the message, press [Close].
E-mail Transmission Error
An error such as a malfunction of the server or disconnection of a network cable has occurred while performing Scan To E-mail. Check the network connection.
To erase the message, press [Close].
Please check SMTP settings.
Cannot connect to the SMTP server. Check the network settings.
Please check POP3 settings.
Cannot connect to the POP3 server. Check the network settings.
SMTP Login failed.
An attempt to log into the SMTP server ended up an authentication error.
Check the network settings.
SMTP Auth. Unsupported
The SMTP server does not support the authentication system.
Check the network settings.
POP3 Login failed.
An attempt to log into the POP3 server ended up an authentication error.
Check the network settings.
Getting target IP failed. Please Check DHCP settings.
The DHCP server cannot be detected. Check the network connection.
Please check DNS settings.
Cannot connect to the DNS server. Check the network connection.
Please check Server settings.
Cannot connect to the file server. Check the network settings.
Server Login failed.
Logging into the file server failed. Check the server settings.
Entering directory failed.
Connecting to the directory of the FTP server failed. Check the server settings.
Changing data Transfer Type failed.
File transmission failed because the file transfer type was not accepted by the FTP server. Change the FTP transfer type to «binary».
File writing failed.
Files sent using Scan To shared folder could not be written. Check the access rights for the shared folder.
FTP destination Full.
Memory in the FTP server is low. Delete unnecessary files and ensure the free space.
Please change File Name.
The specified file name is not acceptable. Check the FTP server settings and change the file name.
Device communication protocol not supported.
The server does not support CIFS or FTP. Check the server settings.
Please check Network Share Name.
The name of the network shared folder is not correct. Check the folder name.
Please check data. Program Data Write Error
An error has occurred when program was being updated.
Please insert USB Memory.
Scan To USB Memory or print from USB Memory with USB Memory not inserted was attempted.
Insert USB Memory.
[TRAY] cassette missing.
The cassette in the indicated tray is pulled out.
Install the cassette.
Access Limitation Error Monochrome printing was performed due to the color printing limitation.
A color print job was converted to a mono print job due to an unauthorized user. Contact your administrator for color printing.
Access Limitation Error Data was deleted due to the color printing limitation.
A color print job was deleted due to an unauthorized user. Contact your administrator for color printing.
Restricted access error Data deleted due to printing restrictions.
A print job was deleted due to an unauthorized user. Contact your administrator for printing.
Incompatible USB device connected. Remove the connected USB device.
An unsupported USB device is connected. Remove the USB device.
Please remove the connected USB device. USB device has not been recognized.
The connected USB device was not recognized. Remove the USB device.
Please remove the USB Hub. USB Hub is connected.
A USB hub is connected. Remove the USB hub. This machine does not support USB hub.
Inspection is required. SIP Error
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
Please call service. Scanner unit failed to detect printer unit.
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
HDD Error 0
While initializing this machine, a hard disk which needs formatting was detected.
HDD Error 250
While initializing this machine, a damaged file for encrypted authentication printing was found. Format the hard disk again.
Accounting Log buffer is near full.
The accounting log buffer is almost full.
Acquire the log and free the buffer.
Accounting Log Writing Error
An accounting log writing error has occurred.
To erase the message, press [Close].
Job Log Database Error
A data base access error has occurred while writing or reading the job log. Turning the machine off and on may resolve the problem.
To erase the message, press [Close].
Accounting Log Buffer Full (Delete old logs)
Old logs were deleted, because accounting log buffer was full. Acquire the log and free the buffer.
Power OFF/ON
Turn the machine off, and then back on. If the same error occurs, contact your dealer.
A decoding error occurred. Check the image data.
An error has occurred in the image data sent to this machine. Check the image data.
Process has been canceled as there is no space on the device. Please free up enough memory space by reducing usage and try again.
Processing data was cancelled due to memory full.
Reduce the usage on the device to ensure available memory, and then retry.
Process has been canceled by a device error. After maintenance or change of the device, please try again.
Processing data was cancelled because an error occurred on the device.
Repair or replace the device, and then retry.
Access denied to PC. Please check PC.
Connecting to a computer failed when performing Scan to Computer. Check the settings on the computer.
Deleting data.
This machine ran out of color toner. Color print data is being deleted.
Error PDF
The PDF file is damaged.
This PDF file is password protected.
This PDF file is password protected. Enter a password to print.
Valid password required to print document.
This PDF needs authentication. Enter a password to print.
No communication with the SNTP server.
Obtaining current time from the SNTP server failed. Check the server.
USB Memory disconnected.
The USB Memory was removed while printing from USB Memory. Do not remove USB Memory while printing is in progress.
Cannot open the file.
The specified file could not be Opened. Check the file.
Cannot read the file.
Files could not be read. Check the device where the files are stored.
File loading from USB.
Data is being read from USB Memory.
Press the Stop button to cancel reading.
An error occurred. Scanning is pending.
Printing has stopped due to an error.
Image Drum Sensor Error.
The toner sensor error has occurred in the image drum indicated on the screen.
Printing was stopped. Rear Output Tray was opened during printing. Open the Output Tray. Error code: 409
The rear output tray was moved while printing.
Place the rear output tray in the correct position, and then open and close the output tray.
Toner empty. Replace with new Toner Cartridge.
The indicated cartridge ran out of toner.
Replace the empty toner cartridge with a new one.
Wait Timeout in menu is disabled. Printing is disabled except by USB. Clear page buffer and enable time out in menu.
Wait Timeout is disabled.
Insufficient memory occurred during Fax Tx reservation.
Insufficient memory error has occurred during Scan To fax.
Insufficient memory.
Insufficient memory error has occurred during fax reception.
E-mail receiving has been cancelled.
E-mail reception was cancelled.
Check the file format and size of the attached file.
Wireless settings are incomplete.
Wrong values are set or items remain unset in the wireless LAN settings. Check the wireless settings.
Not connected to wireless access point.
No wireless LAN access points are found.
Make sure that the access point is turned on.
Disconnect and re-connect to wireless LAN.
Wireless startup failed.
Restart the machine. If the error persists, contact your dealer.
Firmware Update Error Please try again. If network doesn’t work, please try firmware update over USB.
Updating the firmware failed. Update again.
Registering with Google Cloud Print. Don’t turn off the power until registration is complete.
This machine is being registered to the Google Cloud Print service. Wait for a while.
Deleting from Google Cloud Print.
This machine is being removed from the Google Cloud Print service. Wait for a while.
Caution, unknown Consumable detected Go to User Manual «Trouble Shooting» to restore operation Error 709
You can use any consumables in your product, but you must accept the risks of using non-genuine consumables.
If the use of non-genuine consumables causes damage to the product or results in your product not functioning to its full specification, then such damage or effect on the product is not covered by warranty.
To accept these risks and to restore function;
Turn off the machine.
Holding the [CLEAR] button, turn on the machine.
Release the [CLEAR] button when «RAM CHECK 100%» is displayed.
This operation log is recorded in the product.
If you have any questions, contact your dealer.
Replace the image drum. [PAGES] Pages Left.
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Replace the image drum. Print Quality Not Guaranteed.
The image drum indicated on the screen reaches its lifetime.
Replace the image drum with a new one.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
Receiving data timeout.
Data could not received within a certain period of time.
IPv4 address is conflicted. Please change IPv4 address.
The IP address assigned to this machine is duplicated with that of another device.
Check the IP addresses, and then assign another IP address.
Incompatible [COLOR] Image Drum. Error: 984, 685, 686, 687, 690, 691, 692, 693, 700, 701, 702, 703, 704, 705, 706, 707
Non-optimum image drum is installed.
C: Cyan (blue), M: Magenta (red), Y: Yellow, K: Black
C Image Drum Not Installed. Error: 696
Cyan (blue) image drum is not installed.
Install the image drum.
M Image Drum Not Installed. Error: 695
Magenta (red) image drum is not installed.
Install the image drum.
Y Image Drum Not Installed. Error: 694
Yellow image drum is not installed.
Install the image drum.
K Image Drum Not Installed. Error: 697
Black image drum is not installed.
Install the image drum.
Blank pages were detected on all pages. Please check how the document was set.
Scanned pages are all blank. Turn over the document.
In order to set paper that cannot be output to the Upper Output Tray, the paper was output from Output Tray. To turn off this display, press the [Close] button.
Check the type of the specified paper.
Simplex printing was performed as the paper setting did not allow duplex printing.
Duplex printing is not available on the specified paper.
Check the size and thickness of paper.
Multi-purpose tray has not been set to be used as the tray, so multiple copies have been printed. Please verify multi-purpose tray settings. Press [Close] button to remove this dialog
MP tray setting is set to [Do Not Use]. Change the MP tray setting.
Output Paper Full. Remove the paper on [TRAY]. Error: 480, 485
Paper in the output tray is full.
Remove the handout.
Changing Language. Panel operation is disabled.
Display language is being changed.
Wait for a while.
Language Change Failed. Error num: %CODE%
Switching display languages failed. Press the power button to turn the machine off, and then back on.
Detected an abnormality of internal database. The data must be deleted. After pressing [Format], the data will be deleted, and then reboot.
Data base is beyond restoration.
To delete the data base, press [Format].
Cannot print because your Summary Account balance is 0. User name for Printing: [USERNAME] Summary Account Name for Insufficient Balance: [ACCOUNTNAME] To continue the print job, increase the balance and select [Start]. To increase the balance, please contact the device administr. To cancel the print job, select [Cancel].
The number of print jobs excesses the limit. No more print jobs are authorized. Contact your administrator.
Copyright © 2015 Oki Electric Industry Co., Ltd. All rights reserved.
Источник