Pilz pss 3047 3 ошибки

background image

Modular Block System: Emergency Stop Circuits

6-25

The acknowledgements

FbL1 and FbL2 are also monitored in the static

condition. If there are discrepancies between the set and true condition, an
error message will be issued (

ENBL = 0) and the contactors will be

switched off immediately (

K1 = 0 and K2 = 0). The error will need to be

reset.

It is possible to reset errors via the input parameter

RSET both when ON =

0 and when

ON = 1. However, a prerequisite for setting the enable and,

when

ON = 1, switching on the contactors, is that the signals from the

feedback loops are correct.

Error messages

Any fault that is detected will be stored in the corresponding error data
word (

SSNR) of the administration data block (1st data block), until the

fault has been fully dealt with.

• Error messages in the administration data block

— Bit 00:

Fault as the signal changes at input parameter

ON,

feedback loop 1 (

FbL1) remains open

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

— Bit 01:

Fault as the signal changes at input parameter

ON,

feedback loop 1 (

FbL1) remains closed

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

— Bit 02:

Fault as the signal changes at input parameter

ON,

feedback loop 2 (

FbL2) remains open

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

List of Pilz PSS Series Guides:

Guidesimo.com webproject is not a service center of Pilz trademark and does not carries out works for diagnosis and repair of faulty Pilz PSS Series equipment. For quality services, please contact an official service center of Pilz company. On our website you can read and download documentation for your Pilz PSS Series device for free and familiarize yourself with the technical specifications of device.

More Adapter Devices:

  • Paradyne 6512

    TSTLINEALMPWRETHERNETTMTM98-16014a-01TM 1SuperLine AdapterInstallation InstructionsDocument Number 6512-A2-GN10-20January 1999SuperLineAdapterContents: Important Safety Instructions What Your SuperLine Adapter Does Package Checklist Optional Hardware (Not Supplied) Front Panel Indicators SuperLine Adapter Rear Panel Installing Your SuperLine Adapter Troubleshooting Yo …

    6512 Adapter, 28

  • Linksys WPC54G

    F. The Setup Wizard will askyou to review your settingsbefore it starts to copy files.Click Next if you are satis-fied with your settings, orclick Back to change anysettings. G. After the files have beensuccessfully copied, youwill see Figure G. Click theExit button.Proceed to Step 2.WPC54GPackage Contents• One Wireless-G Notebook Adapter (1)• One Setup Wizard CD-ROM with UserGuide (2)• On …

    WPC54G Adapter, 2

  • Mini Gadgets LMWiFiPower

    Updated 06/30/2016 1 Version 1.0 POWER ADAPTER WITH HIDDEN CAMERA SKU: LMWiFiPower THANK YOU FOR PURCHASING THE LMWIFIPOWER Please read this manual before operating the LMWiFiPower and keep it handy. The most ubiquitous, unnoticeable devices nowadays are chargers. With the average Joe carrying at least two or three rechargeable electronic devices on their person every da …

    LMWiFiPower Adapter, 5

  • D-Link DFE-530TX

    Contents of Package: • DFE-530TX+ Ethernet PCI Adapter • Printed Quick Installation Guide • CD with Manual and Drivers If any of the above items are missing, please contact your reseller. Before you start, make sure to turn off your computer and unplug the power cord. Note: To avoid damage caused by static electricity, make sure to properly ground yourself by first touching a metal par …

    DFE-530TX Adapter, 6

Recommended Documentation:

  • 5 Янв 2007

Контроллер Pilz PSS3100 — коды сообщений.
Суть проблемы: листогиб AMADA. В состав входят ЧПУ на Ampro LittleBoard и контроллер Pilz. После простоя 4 дня в холоде включили — выскочила ошибка готовности контролера. Сервисные московсие фирмы на каникулах. У нас ни схем, ни документации, ни программ для контроллера.
Внешне проверяли релюшки, датчики, разъемы — все в порядке. Научный тык не прошел.
Вопрос может кто владеет информацией по расшифровке кодов, отображаемых на LED контроллера?

  • 5 Янв 2007

Покопайся на  ссылка скрыта от публикации  в разделе Download. Может найдешь чего…

  • 7 Янв 2007

Копался… и на  ссылка скрыта от публикации / тоже… даже зарегился там и в техподдержке спросил, однако молчат.

  • 8 Янв 2007

Кстати, станок подняли. Решение пришло элементарное. Раз станок от холода загнулся, надо его прогреть.
Взяли, да и прогрели тепловентилятором электрошкаф с контроллером и ЧПУ — ошибка исчезла.
НО вопрос по кодам не снимаю. Надо бы узнать, чему именно не нравиться холод. Почему-то другие станки нормально его перенесли.

Источник

Commissioning and Operation

If the module has not achieved the correct operating status, there are

several options available for error diagnostics:

• Evaluating the operating status LED

• Evaluating the output paramter ERR of SB 236

(see ST SB ControlNet — Software Manual)

• Evaluating the data block for status information DB_S

(see ST SB ControlNet — Software Manual)

• Bus diagnostics via the NAP-interface for the module

For this purpose an additional monitoring tool is required. Further

information can be found in the relevant operating mnaual for the

monitoring tool.

Operation

The module is operated on ControlNet using a software package from

Pilz. It contains the standard function block SB 236 which runs in the

standard section of the PSS. It is used for communication between the

PSS and other ControlNET subscribers (send/receive data).

More detailed information on SB 236 can be found in a separate operating

manual «ST SB ControlNet — Software Manual». This is supplied with the

software package.

7-2

PSS(1) ControlNet Adapter — Hardware Manual

Источник

background image

Modular Block System: Emergency Stop Circuits

6-25

The acknowledgements

FbL1 and FbL2 are also monitored in the static

condition. If there are discrepancies between the set and true condition, an
error message will be issued (

ENBL = 0) and the contactors will be

switched off immediately (

K1 = 0 and K2 = 0). The error will need to be

reset.

It is possible to reset errors via the input parameter

RSET both when ON =

0 and when

ON = 1. However, a prerequisite for setting the enable and,

when

ON = 1, switching on the contactors, is that the signals from the

feedback loops are correct.

Error messages

Any fault that is detected will be stored in the corresponding error data
word (

SSNR) of the administration data block (1st data block), until the

fault has been fully dealt with.

• Error messages in the administration data block

— Bit 00:

Fault as the signal changes at input parameter

ON,

feedback loop 1 (

FbL1) remains open

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

— Bit 01:

Fault as the signal changes at input parameter

ON,

feedback loop 1 (

FbL1) remains closed

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

— Bit 02:

Fault as the signal changes at input parameter

ON,

feedback loop 2 (

FbL2) remains open

Remedy: Check contactor, contacts, cable, input card, output
card, value of input parameter

TFbL and all conditions and

then reset (input parameter

RSET)

Источник

+7 (495) 215-16-67

8 (800) 333-16-67

с 9:00-19:00 — ежедневно (МСК)

Заказать звонок

×

Обратный звонок

Представьтесь

Номер вашего телефона

Ваш вопрос

я даю согласие Shopozz на обработку персональных данных
в соответствии с Федеральным законом от 27.07.2006 года №152-ФЗ «О персональных данных», на условиях и для целей, определенных Политикой конфиденциальности.

×

Доставка товаров с аукциона eBay и интернет-магазинов США в
Россию (Москва, Санкт-Петербург, Новосибирск, Екатеринбург,
Казань, Нижний Новгород, Челябинск, Красноярск, Самара, Уфа,
Ростов-на-Дону, Омск, Краснодар, Воронеж, Волгоград, Пермь и
другие города).

© Shopozz — сервис покупок за рубежом

Источник

Guidesimo.com webproject is not a service center of Pilz trademark and does not carries out works for diagnosis and repair of faulty Pilz PSS Series equipment. For quality services, please contact an official service center of Pilz company. On our website you can read and download documentation for your Pilz PSS Series device for free and familiarize yourself with the technical specifications of device.

More Adapter Devices:

  • SIIG VV-CV0012-S1

    1Introducing the DP ADD2 PCIe DVI AdapterThe DP ADD2 PCIe DVI Adapter is an economical way toadd a second monitor to PCs using select Intel PCIExpress based graphics controllers. Increase yourproductivity by using it as an extended desktop or as alarger/different display for your main screen.Features and Benefits• Adds a DVI-D port for an additional monitor• Multiple display functionality: pr …

    VV-CV0012-S1 Adapter, 8

  • ZyXEL Communications G-220 V2

    Copyright © 2008. All rights reservedZyXEL G-220 v2802.11g Wireless USB AdapterQuick Start GuideVersion 2.1.13/2008Edition 1CONTENTSENGLISH 2 DEUTSCH 14 ESPANOL 26 FRANCAIS 38 ITALIANO 50 РУССКИЙ 62 SVENSKA 74 繁體中文 86 …

    G-220 V2 Adapter, 95

  • D-Link DG-102S

    DG-102S Thank you for choosing the D-Link DG-102S, the value leader for VoIP products. The D-Link DG-102S VoIP Station Gateway links traditional telephony networks to IP networks with conventional telephony devices such as analog phones or fax machines. The DG-102S includes two loop start Foreign Exchange Subscriber (FXS) interfaces with normal RJ-11 telephone connectors that provide voice/fax c …

    DG-102S Switch, 1

  • SanDisk Connect

    Getting Startedfor Connect Wireless StickPlug the SanDisk Connect™ Wireless Stick into a computer or USB-AC adapter to ensure that it’s fully charged. A full charge can take up to 2 hours. Device cannot be connected using a USB cable.Download and install the SanDisk Connect app on your mobile device. SanDisk® has many apps available, so please ensure you select the correct application, matchi …

    Connect Adapter, 1

  • Tripp Lite U437-001-C

    11111 W. 35th Street, Chicago, IL 60609 USA tripplite.com/supportCopyright © 2020 Tripp Lite.USB-C to 3.5 mm Audio Adapter with PD ChargingModel: U437-001-COwner’s ManualEste manual esta disponible en español en la página de Tripp Lite: tripplite.comCe manuel est disponible en français sur le site Web de Tripp Lite : tripplite.comtРусскоязычная версия настоящего …

    U437-001-C Adapter, 8

Recommended Documentation:
Источник

Понравилась статья? Поделить с друзьями:
  • Pillars of eternity ошибка the game crashed
  • Pigma ultra system 25 ff ошибка
  • Pidgin ошибка при загрузке среды gtk
  • Pid 411 ошибка volvo vnl
  • Pid 27 код ошибки вольво vnl