Ошибка printer halted kill called

Всем привет! Вчера, на середине печати мой принтер написал ошибку и прекратил печать!

Термисторы стоят китайские..

Пытался ставить минимальную температуру в 5 градусов, не помогло….

READ: Error:Thermal Runaway, system stopped! Heater_ID: bed

READ: Error:Printer halted. kill() called!

Вот вырезки из конфига

:

//#define TEMP_SENSOR_0 1

#define TEMP_SENSOR_0 5

#define TEMP_SENSOR_1 0

#define TEMP_SENSOR_2 0

#define TEMP_SENSOR_3 0

//#define TEMP_SENSOR_BED 0

#define TEMP_SENSOR_BED 1

// The minimal temperature defines the temperature below which the heater will not be enabled It is used

// to check that the wiring to the thermistor is not broken.

// Otherwise this would lead to the heater being powered on all the time.

#define HEATER_0_MINTEMP 5

#define HEATER_1_MINTEMP 5

#define HEATER_2_MINTEMP 5

#define HEATER_3_MINTEMP 5

#define BED_MINTEMP 5

// When temperature exceeds max temp, your heater will be switched off.

// This feature exists to protect your hotend from overheating accidentally, but *NOT* from thermistor short/failure!

// You should use MINTEMP for thermistor short/failure protection.

// Ограничение максимальной температуры хотэнда

#define HEATER_0_MAXTEMP 275

#define HEATER_1_MAXTEMP 275

#define HEATER_2_MAXTEMP 275

#define HEATER_3_MAXTEMP 275

#define BED_MAXTEMP 120

When printing cube.gcode using Pronterface I get:

Print started at: 23:07:31

After 8 seconds I get:

Error:Printer halted. kill() called!
Error:Printer halted. kill() called!

What is the reason?
How can I see logs?

Additional information:

I connected only three motors, and set the following in Configuration.h of Marlin Firmware:

#define TEMP_SENSOR_0 999
...
#define TEMP_SENSOR_BED 999
...
#define X_MIN_ENDSTOP_INVERTING true // set to true to invert the logic of the endstop.
...

(Also for min max for XYZ)

In 8 second X motor and Z motor were running.

This is the link to G-Code print file (cube.gcode).

I’m using Marlin 1.1.x on a Arduino Mega 2560 + RAMPS 1.4 without endstops.

/**
 * Thermal Protection provides additional protection to your printer from damage
 * and fire. Marlin always includes safe min and max temperature ranges which
 * protect against a broken or disconnected thermistor wire.
 *
 * The issue: If a thermistor falls out, it will report the much lower
 * temperature of the air in the room, and the the firmware will keep
 * the heater on.
 *
 * If you get "Thermal Runaway" or "Heating failed" errors the
 * details can be tuned in Configuration_adv.h
 */

#define THERMAL_PROTECTION_HOTENDS // Enable thermal protection for all extruders
#define THERMAL_PROTECTION_BED     // Enable thermal protection for the heated bed

   /**
   * Whenever an M104, M109, or M303 increases the target temperature, the
   * firmware will wait for the WATCH_TEMP_PERIOD to expire. If the temperature
   * hasn't increased by WATCH_TEMP_INCREASE degrees, the machine is halted and
   * requires a hard reset. This test restarts with any M104/M109/M303, but only
   * if the current temperature is far enough below the target for a reliable
   * test.
   *
   * If you get false positives for "Heating failed", increase WATCH_TEMP_PERIOD
   * and/or decrease WATCH_TEMP_INCREASE. WATCH_TEMP_INCREASE should not be set
   * below 2.
   */
  #define WATCH_TEMP_PERIOD 20                // Seconds
  #define WATCH_TEMP_INCREASE 2               // Degrees Celsius