Я так понимаю проблемма с соленоидом переключения 2-й передачи.
Залез под машину и не вижу никаких разъёмов кроме 2-х датчиков, видимо вращение вылов.
Не могу найти эл.схему подключения АТ, на паджерик этих годов.
Видимо всё внутри и управление цыфрой по КАНу?
У кого есть схема скиньте пжлста.
VIN
MMCGYKH40BFZ07550
Изменено 17 мая 2017 пользователем sovg
Тощий
Сообщения: 10
Зарегистрирован: 11 ноя 2012, 11:15
Двигатель:: 3.8 250
Мой автомобиль(и):: Паджеро 4
Откуда: г.Тула тульской области
Р1775 ошибка АКПП
коробка при движении упала в аварию(включилась 3 передача) загорелся чек, диагностика говорит ошибка АКПП Р1775 (ошибка второго соленойда) скинули ошибку через 3км. тоже самое. Подскажите куда лесть в проводку или в саму АКПП.
Механик
Сообщения: 266
Зарегистрирован: 03 июн 2009, 17:14
Откуда: 97
Поблагодарили: 4 раза
Re: Р1775 ошибка АКПП
Сообщение
Механик » 13 янв 2015, 23:28
на карман скан есть режим тестирования клапанов акпп и в зависимости от того будет тестироваться или нет решать что делать дальше
П-2 4м40, П-3 4м41
Найдена следующая информация по ошибке P1775 для автомобиля MITSUBISHI PAJERO SPORT (2008-2014), KH:
На русском языке:
Ошибка системы передачи MIL
На английском языке:
Transmission System MIL Fault
Вы можете задать вопрос или поделиться опытом устранения ошибки P1775 на автомобиле MITSUBISHI с другими пользователями.
Возможную причину возникновения и советы по устранению можно найти в каталоге причин и советов:
Найти причину >>>
Ошибки (коды ошибок) полученные от прибора, сканера требуют правильной интерпретации информации, дабы не тратить время и деньги на замену работающих элементов автомобиля.
Проблема зачастую кроется намного глубже чем кажется на первый взгляд. Это& вызвано теми обстоятельствами, что информационные сообщения содержат, как было выше сказано, косвенную информацию о нарушении работы системы.
Может быть полезным для решения вопроса по устранению неисправности у Mitsubishi Pajero Sport (KH):
Возможные причины: Нет обмена данными между ECM и TCM из-за внутренней неисправности в коммутаторе; Неисправный датчик кривошипа.
Снимите клапан рециркуляции отработавших газов (всего два болта и электрический разъем) и проверьте, не заклинило ли игольчатый клапан и не нагара ли. При толкании он должен свободно двигаться. Если он вешается и не закрывается должным образом, это может быть проблемой.
OPERATION
The ECU detects the current gear/speed according to the output signals from the
input and output shaft speed sensor.
DIAGNOSIS CODE SET CONDITIONS
If the output from the output shaft speed sensor multiplied by the gear ratio is not the
same as the output from the input shaft speed sensor after completing of shifting, the corresponding
diagnosis code is set. If each diagnosis code is set 4 times, the transmission is fixed in 3rd as a fail-safe
measure.
PROBABLE CAUSES
Malfunction of input shaft speed sensor
Malfunction of output shaft speed sensor
Damaged harness wires and connectors
Malfunction of the A/T-ECU
Malfunction of solenoid valve
Malfunction of reverse clutch retainer
Malfunction of valve body
Malfunction of direct planetary carrier
Malfunction of low-reverse brake system (for diagnosis codes P1779, P1784)
Malfunction of underdrive clutch system (for diagnosis codes P1779, P1780, P1781,
P1782)
Malfunction of second brake system (for diagnosis codes P1780, P1783)
Malfunction of overdrive clutch system (for diagnosis codes P1781, P1782, P1783)
Malfunction of reverse clutch system (for diagnosis code P1784)
Malfunction of direct clutch system (for diagnosis codes P1782, P1783)
Malfunction of reduction brake system (for diagnosis codes P1779, P1780, P1781,
P1784)
Malfunction of one-way clutch system (for diagnosis code P1779)
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III diagnosis code
Either of diagnosis codes P1779, P1780, P1781, P1782, P1783 or P1784 is set, the input
shaft speed sensor or output shaft speed sensor is defective.
Q.
Are diagnosis codes P1766 (P0715) or P1767 (P0720) set?
YES diagnosis code P1766 (P0715) is set : Refer to diagnosis code P1766 (P0715) input shaft speed sensor system .
YES diagnosis code P1767 (P0720) is set : Refer to diagnosis code P1767 (P0720) output shaft speed sensor system .
Go to Step 2.
STEP 2. M.U.T.-III diagnosis code
Either of diagnosis codes P1779, P1780, P1781, P1782, P1783 or P1784 is set, the corresponding
solenoid valve is defective.
Q.
Is either of diagnosis code P1773 (P0750), P1774 (P0755), P1775 (P0760), P1776 (P0765),
P1777 (P0770) set?
YES diagnosis code P1773 (P0750) is set : Refer to diagnosis code P1773 (P0750): Low-reverse solenoid valve system .
YES diagnosis code P1774 (P0755) is set : Refer to diagnosis code P1774 (P0755): Underdrive solenoid valve system .
YES diagnosis code P1775 (P0760) is set : Refer to diagnosis code P1775 (P0760): Second solenoid valve system .
YES diagnosis code P1776 (P0765) is set : Refer to diagnosis code P1776 (P0765): Overdrive solenoid valve system .
YES diagnosis code P1777 (P0770) is set : Refer to diagnosis code P1777 (P0770): Reduction solenoid valve system .
Go to Step 3.
STEP 3. Hydraulic pressure test
Each hydraulic pressure of the elements below, which diagnosis codes indicate, should
be within the standard value.
NO some hydraulic pressures are abnormal : Go to Step 5.
NO all hydraulic pressure are abnormal : Go to Step 4.
STEP 4. Adjust the line pressure and recheck the diagnosis code.
(1)Adjust the line pressure (Refer to ).
(2)Test drive the vehicle.
(3)Check the diagnosis code.
Q.
Is the diagnosis code set?
Go to Step 5.
The inspection is complete.
STEP 5. Disassemble, clean and assemble the valve body and recheck
the diagnosis code.
(1)Check the mounting bolts for looseness, and the O-ring, solenoid valve and valve
body for damage. Replace the valve body assembly if the damages are thought to be irreparable.
(2)Test drive the vehicle.
(3)Check the diagnosis code.
Q.
Is the diagnosis code set?
Go to Step 7.
The inspection is complete.
STEP 6. Replace the A/T-ECU and then recheck the diagnosis code.
(2)Test drive the vehicle.
(3)Check the diagnosis code.
Q.
Is the diagnosis code set?
Go to Step 7.
The inspection is complete.
STEP 7. Check the A/T internal clutch and brake, and then
recheck the diagnosis code.
(1)Check the following clutches or brakes according to the output diagnosis codes,
replace if necessary.
If diagnosis code P1779, P1780, P1781, P1782 are set individually or in a
group, replace the underdrive clutch.
If diagnosis code P1781, P1782, P1783 are set individually or in a group, replace
the overdrive clutch.
If diagnosis code P1784 is set, replace the reverse clutch.
If diagnosis code P1779, P1784 are set individually or in a group, replace the low-reverse
brake.
If diagnosis code P1780, P1783 are set individually or in a group, replace the second
brake.
If diagnosis code P1782, P1783 are set individually or in a group, replace the direct
clutch.
If diagnosis code P1779, P1780, P1781, P1784 are set individually or in a group,
replace the reduction brake.
If diagnosis code P1779 is set, replace the one-way clutch.
(2)Test drive the vehicle.
(3)Check the diagnosis code.
Q.
Is the diagnosis code set?
Eliminate the cause of the noise.
The inspection is complete.
MMC-Manuals.ru
Ошибки полученные от прибора (сканера) требуют правильной интерпретации полученной от него информации, дабы не тратить время и деньги на замену работающих элементов автомобиля.
Вам может быть полезна информация для устранения неисправности:
Возможные причины: Нет обмена данными между ECM и TCM из-за внутренней неисправности в коммутаторе; Неисправный датчик кривошипа.
Снимите клапан рециркуляции отработавших газов (всего два болта и электрический разъем) и проверьте, не заклинило ли игольчатый клапан и не нагара ли. При толкании он должен свободно двигаться. Если он вешается и не закрывается должным образом, это может быть проблемой.
коробка при движении упала в аварию(включилась 3 передача) загорелся чек, диагностика говорит ошибка АКПП Р1775 (ошибка второго соленойда) скинули ошибку через 3км. тоже самое. Подскажите куда лесть в проводку или в саму АКПП.
Механик
Сообщения: 266
Зарегистрирован: 03 июн 2009, 17:14
Откуда: 97
Поблагодарили: 4 раза
Re: Р1775 ошибка АКПП
Сообщение
Механик » 13 янв 2015, 23:28
на карман скан есть режим тестирования клапанов акпп и в зависимости от того будет тестироваться или нет решать что делать дальше
Найдена следующая информация по ошибке P1775 для автомобиля MITSUBISHI PAJERO SPORT (2008-2014), KH:
На русском языке:
Ошибка системы передачи MIL
На английском языке:
Transmission System MIL Fault
Вы можете задать вопрос или поделиться опытом устранения ошибки P1775 на автомобиле MITSUBISHI с другими пользователями.
Возможную причину возникновения и советы по устранению можно найти в каталоге причин и советов:
Найти причину >>>
Ошибки (коды ошибок) полученные от прибора, сканера требуют правильной интерпретации информации, дабы не тратить время и деньги на замену работающих элементов автомобиля.
Проблема зачастую кроется намного глубже чем кажется на первый взгляд. Это& вызвано теми обстоятельствами, что информационные сообщения содержат, как было выше сказано, косвенную информацию о нарушении работы системы.
Может быть полезным для решения вопроса по устранению неисправности у Mitsubishi Pajero Sport (KH):
Возможные причины: Нет обмена данными между ECM и TCM из-за внутренней неисправности в коммутаторе; Неисправный датчик кривошипа.
Снимите клапан рециркуляции отработавших газов (всего два болта и электрический разъем) и проверьте, не заклинило ли игольчатый клапан и не нагара ли. При толкании он должен свободно двигаться. Если он вешается и не закрывается должным образом, это может быть проблемой.
The ECU detects the current gear/speed according to the output signals from the
input and output shaft speed sensor.
DIAGNOSIS CODE SET CONDITIONS
If the output from the output shaft speed sensor multiplied by the gear ratio is not the
same as the output from the input shaft speed sensor after completing of shifting, the corresponding
diagnosis code is set. If each diagnosis code is set 4 times, the transmission is fixed in 3rd as a fail-safe
measure.
PROBABLE CAUSES
Malfunction of input shaft speed sensor
Malfunction of output shaft speed sensor
Damaged harness wires and connectors
Malfunction of the A/T-ECU
Malfunction of solenoid valve
Malfunction of reverse clutch retainer
Malfunction of valve body
Malfunction of direct planetary carrier
Malfunction of low-reverse brake system (for diagnosis codes P1779, P1784)
Malfunction of underdrive clutch system (for diagnosis codes P1779, P1780, P1781,
P1782)
Malfunction of second brake system (for diagnosis codes P1780, P1783)
Malfunction of overdrive clutch system (for diagnosis codes P1781, P1782, P1783)
Malfunction of reverse clutch system (for diagnosis code P1784)
Malfunction of direct clutch system (for diagnosis codes P1782, P1783)
Malfunction of reduction brake system (for diagnosis codes P1779, P1780, P1781,
P1784)
Malfunction of one-way clutch system (for diagnosis code P1779)
DIAGNOSIS PROCEDURE
STEP 1. M.U.T.-III diagnosis code
Either of diagnosis codes P1779, P1780, P1781, P1782, P1783 or P1784 is set, the input
shaft speed sensor or output shaft speed sensor is defective.
Q.
Are diagnosis codes P1766 (P0715) or P1767 (P0720) set?
YES diagnosis code P1766 (P0715) is set : Refer to diagnosis code P1766 (P0715) input shaft speed sensor system .
YES diagnosis code P1767 (P0720) is set : Refer to diagnosis code P1767 (P0720) output shaft speed sensor system .
Go to Step 2.
STEP 2. M.U.T.-III diagnosis code
Either of diagnosis codes P1779, P1780, P1781, P1782, P1783 or P1784 is set, the corresponding
solenoid valve is defective.
Q.
Is either of diagnosis code P1773 (P0750), P1774 (P0755), P1775 (P0760), P1776 (P0765),
P1777 (P0770) set?
YES diagnosis code P1773 (P0750) is set : Refer to diagnosis code P1773 (P0750): Low-reverse solenoid valve system .
YES diagnosis code P1774 (P0755) is set : Refer to diagnosis code P1774 (P0755): Underdrive solenoid valve system .
YES diagnosis code P1775 (P0760) is set : Refer to diagnosis code P1775 (P0760): Second solenoid valve system .
YES diagnosis code P1776 (P0765) is set : Refer to diagnosis code P1776 (P0765): Overdrive solenoid valve system .
YES diagnosis code P1777 (P0770) is set : Refer to diagnosis code P1777 (P0770): Reduction solenoid valve system .
Go to Step 3.
STEP 3. Hydraulic pressure test
Each hydraulic pressure of the elements below, which diagnosis codes indicate, should
be within the standard value.
NO some hydraulic pressures are abnormal : Go to Step 5.
NO all hydraulic pressure are abnormal : Go to Step 4.
STEP 4. Adjust the line pressure and recheck the diagnosis code.
(1)Adjust the line pressure (Refer to ).
(2)Test drive the vehicle.
(3)Check the diagnosis code.
Q.
Is the diagnosis code set?
Go to Step 5.
The inspection is complete.
STEP 5. Disassemble, clean and assemble the valve body and recheck
the diagnosis code.
(1)Check the mounting bolts for looseness, and the O-ring, solenoid valve and valve
body for damage. Replace the valve body assembly if the damages are thought to be irreparable.
(2)Test drive the vehicle.
(3)Check the diagnosis code.
Q.
Is the diagnosis code set?
Go to Step 7.
The inspection is complete.
STEP 6. Replace the A/T-ECU and then recheck the diagnosis code.
(2)Test drive the vehicle.
(3)Check the diagnosis code.
Q.
Is the diagnosis code set?
Go to Step 7.
The inspection is complete.
STEP 7. Check the A/T internal clutch and brake, and then
recheck the diagnosis code.
(1)Check the following clutches or brakes according to the output diagnosis codes,
replace if necessary.
If diagnosis code P1779, P1780, P1781, P1782 are set individually or in a
group, replace the underdrive clutch.
If diagnosis code P1781, P1782, P1783 are set individually or in a group, replace
the overdrive clutch.
If diagnosis code P1784 is set, replace the reverse clutch.
If diagnosis code P1779, P1784 are set individually or in a group, replace the low-reverse
brake.
If diagnosis code P1780, P1783 are set individually or in a group, replace the second
brake.
If diagnosis code P1782, P1783 are set individually or in a group, replace the direct
clutch.
If diagnosis code P1779, P1780, P1781, P1784 are set individually or in a group,
replace the reduction brake.
If diagnosis code P1779 is set, replace the one-way clutch.